What did you do today?

Guest · Post by **Guest** » Sun Sep 06, 2020 2:16 pm

I think the belt had gone hard, pulleys were ok, back home now as the RAC bloke was old school and had a selection of belts on his van, one of which fitted. He bled and topped up the coolant and it's driven home fine. It could have been worse.

fried onions · Post by **fried onions** » Sun Sep 06, 2020 8:00 pm

You will be keeping a spare in the boot now... don't rely on the belt the chap fitted to be the right one.

Post by **Hooli** » Sun Sep 06, 2020 8:05 pm

Whenever I service a car, I put the old belt etc in the boot. You never know when you might be thankful for it.

AMCrebel · Post by **AMCrebel** » Sun Sep 06, 2020 9:41 pm

Took the rear bumper off the spare AMC to fit to the running one.

DodgeRover · Post by **DodgeRover** » Sun Sep 06, 2020 10:26 pm

AMCrebel wrote: ↑Sun Sep 06, 2020 9:41 pm Took the rear bumper off the spare AMC to fit to the running one.

Isn't it about time we had some pictures of the UKs only AMC stash?

SiC · Post by **SiC** » Mon Sep 07, 2020 12:09 am

Second hand timing tool set arrived today for the Clio, so I can get on with removing the crank pulley.

: IMG_20200906_180527.jpg (711.72 KiB) Viewed 3300 times

Timing is way out

These should just freely slide in and out of that slot

Looks like a full on cambelt job then to sort this properly! Basically worse case scenario with his job and becoming significant project creep.

Supposed to replace the dephaser pulley. Basically it's a pulley that fills with oil and does the variable valve timing magic. Thinking may not as they're £150 on their own.

Post by **Hooli** » Mon Sep 07, 2020 6:59 am

That's a lot closer than an ex's fiestering when a so called professional mechanic did the head gasket. They use a similar tool across the end of the head & on both cams one slot was totally above the tool & one below. I think it had two or three teeth of belt extra between the cams.

AMCrebel · Post by **AMCrebel** » Mon Sep 07, 2020 8:48 am

DodgeRover wrote: ↑Sun Sep 06, 2020 10:26 pm
AMCrebel wrote: ↑Sun Sep 06, 2020 9:41 pm Took the rear bumper off the spare AMC to fit to the running one.
Isn't it about time we had some pictures of the UKs only AMC scrapyard?

OK then

: IMG_1962.JPG (535.53 KiB) Viewed 3285 times

: IMG_1959.JPG (611 KiB) Viewed 3285 times

: IMG_1958.JPG (658.39 KiB) Viewed 3285 times

panhard65 · Post by **panhard65** » Mon Sep 07, 2020 9:24 am

With the clio timing tool there should be a bit of movement on the cams just turn them slightly and they will line up. The crank is the important bit to get set as that has the floating pulley.

SiC · Post by **SiC** » Mon Sep 07, 2020 9:38 am

panhard65 wrote: ↑Mon Sep 07, 2020 9:24 am With the clio timing tool there should be a bit of movement on the cams just turn them slightly and they will line up. The crank is the important bit to get set as that has the floating pulley.

That's all currently locked up, so I'll need to undo the pulleys and make them floating to get them aligned up. Hence why as I might as well change the belt while I'm there.

You're probably the best person on here to know about them as you have dealt a lot with Laguna's and the like, but Dephasers. What's your experience of them failing? Especially after a belt job?

What did you do today?

Re: What did you do today?

Re: What did you do today?

Re: What did you do today?

Re: What did you do today?

Re: What did you do today?

Re: What did you do today?

Re: What did you do today?

Re: What did you do today?

Re: What did you do today?

Re: What did you do today?